Greenhouse Temperature Control · Pillar guide

How to Size a Greenhouse Heater: BTU Heat-Loss Worksheet

Calculate greenhouse heater output from exposed surface area, glazing heat loss, local design temperature, air leakage, and base perimeter—then test the result in BTU/h and watts.

Evidence-led guide
On this page

    Size a greenhouse heater from hourly heat loss, not floor area alone. Add heat loss through the exposed roof and walls (A × U × ΔT), natural air leakage (0.02 × V × ACH × ΔT), and the base perimeter when applicable. Then compare that delivered BTU/h requirement with the heater’s rated output. Roof shape, glazing, leaks, and local winter design temperature can make two greenhouses with the same floor area need different heaters.

    Use this greenhouse heat-loss worksheet

    The worksheet estimates a steady hourly design load. It does not predict seasonal energy cost, warm-up time, solar gain, or the coldest temperature ever recorded. Keep every input visible so you can rerun the calculation when the covering, target temperature, or leakage condition changes.

    TermFormulaInput you need
    Covering and frame lossQconduction = Σ(A × U × ΔT)Exposed area for each assembly, its U-factor, and temperature difference
    Natural air leakageQinfiltration = 0.02 × V × ACH × ΔTInterior volume and estimated natural air changes per hour
    Base perimeter, when usedQperimeter = P × F × ΔTGround-contact perimeter and the selected perimeter factor
    Total delivered heatQtotal = Qconduction + Qinfiltration + QperimeterAll applicable losses in BTU/h
    Electric output equivalentwatts = Qtotal ÷ 3.412Total delivered BTU/h
    Units: area in ft², U in Btu/(h·ft²·°F), volume in ft³, perimeter in ft, and ΔT in °F. The method follows UGA and UAF Extension heat-loss guidance.

    Calculate unlike surfaces separately. A polycarbonate end wall, inflated double-film roof, insulated knee wall, and door do not share one U-factor. Adding the four component losses is more defensible than averaging materials into one convenient number.

    1. Set indoor and outdoor design temperatures

    Choose the lowest indoor temperature your crop and operating plan require at night. That target is a project decision, not a universal greenhouse setpoint. For the outdoor input, use a nearby station’s heating design dry-bulb temperature rather than a normal low or a record extreme.

    The ASHRAE Handbook presents 99% and 99.6% heating design conditions. In a typical year, colder conditions occur for roughly 88 hours at the 99% value and 35 hours at the 99.6% value. The more conservative choice increases heater capacity, but neither is a promise against every extreme. Match the design condition to crop consequence, backup heat, power reliability, and local professional requirements.

    Subtract the outdoor design temperature from the indoor target. A 45°F target and 10°F outdoor design temperature give ΔT = 35°F. Use that same ΔT in each term unless a boundary, such as an attached heated wall, has a different temperature.

    2. Measure exposed area, volume, and perimeter

    For a simple gable greenhouse, record width W, length L, eave height He, and ridge height Hr. The roof slope length is not half the width; calculate the diagonal first.

    MeasurementGable-greenhouse formula
    One roof slopes = √[(W ÷ 2)² + (Hr − He)²]
    Both roof planes2 × L × s
    Both sidewalls2 × L × He
    Both end walls2 × [W × He + ½ × W × (Hr − He)]
    Interior volumeW × L × He + ½ × W × (Hr − He) × L
    Ground perimeter2 × (W + L)
    Measure the actual exterior planes. Subtract or separate doors, opaque knee walls, and attached boundaries only when you also calculate their different U-factor and temperature condition.

    For a curved roof, lean-to, dome, or irregular house, use the manufacturer’s exterior surface area or calculate each real plane or arc. Do not force curved glazing into the gable formula. Floor area remains useful for layout, but it is not the heat-transfer area.

    3. Choose U-factors and bracket air leakage

    A U-factor describes heat transmission: a lower value means less heat loss for the same area and temperature difference. Use current documentation for the exact covering assembly first. Thickness alone does not lock the result; air spaces, cell geometry, coatings, framing, seals, and the test basis can change performance.

    Covering assemblyFallback U-factor, Btu/(h·ft²·°F)Use
    Single plastic film1.20–1.25Run both ends if exact data is unavailable
    Single glass1.10–1.20Separate insulated opaque sections
    Separated or inflated double plastic film0.70–0.80Assumes the air layer is maintained
    Double acrylic or polycarbonate assembly0.50–0.60Fallback only; exact panel data is stronger
    Bounded starting values synthesized from UGA Bulletin 792 and the UAF greenhouse environment guide.

    Air leakage is less certain without measurement. UGA lists 0.5–1.0 ACH for new double-layer film houses, 0.75–1.0 for new glass or fiberglass, 1.0–2.0 for older glass in good condition, and 2.0–4.0 for older glass in poor condition. A hobby polycarbonate kit does not map cleanly to those categories. Choose a defensible low and high case, calculate both, and keep the range visible.

    UGA’s simplified base term uses F = 0.8 Btu/(h·ft·°F) for an uninsulated perimeter and 0.4 for its insulated condition. Treat this as a screening term, not a substitute for a site-specific ground-loss model. If a supplier or engineer provides a different method, do not add both and count the same loss twice.

    Worked example: an 8 × 12 ft gable greenhouse

    This is a hypothetical arithmetic example, not a measured greenhouse. Assume an 8 ft width, 12 ft length, 6.5 ft eave, 9 ft ridge, double polycarbonate fallback U = 0.60, 45°F indoor target, 10°F outdoor design temperature, 1.0 ACH, and an uninsulated base factor of 0.8.

    StepArithmeticResult
    Roof slope√(4² + 2.5²)4.717 ft
    Exposed envelope2(12×6.5) + 2[(8×6.5)+(½×8×2.5)] + 2(12×4.717)393.21 ft²
    Interior volume(8×12×6.5) + (½×8×2.5×12)744 ft³
    Ground perimeter2(8+12)40 ft
    Conduction393.21×0.60×358,257 BTU/h
    Infiltration0.02×744×1.0×35521 BTU/h
    Perimeter40×0.8×351,120 BTU/h
    Total delivered heat8,257+521+1,1209,898 BTU/h
    Electric output equivalent9,898÷3.4122,901 W
    Rounded results. Replacing 1.0 ACH with 2.0 ACH raises this example to about 10,419 BTU/h, or 3,054 W.

    The sensitivity pass changes a guess into a range. It also shows which improvement matters: lowering the target, using a better documented covering assembly, sealing known gaps, or insulating the base can be compared by changing one input and rerunning the same sheet. Do not add a generic reserve after already choosing a high leakage case unless the equipment-selection method explicitly requires it.

    4. Convert the load into a heater decision

    Match the result to rated delivered output. UAF Extension specifically warns to use heater output rather than input. If a combustion heater lists only fuel input, use its current certified output or exact rated thermal efficiency; do not assume an efficiency percentage. For electric resistance output, the energy conversion is 1,000 W = 3,412 BTU/h, so a 1,500 W heater corresponds to about 5,118 BTU/h.

    The worked example needs roughly 2,901–3,054 W under its stated leakage cases. That means a single 1,500 W portable heater cannot meet the calculated design load. This is a design stop, not permission to improvise power. The US Consumer Product Safety Commission says portable electric space heaters should plug directly into a wall outlet, never an extension cord or power strip.

    Verify the exact heater listing, nameplate, damp-location suitability, clearances, controller compatibility, receptacle, branch circuit, and locally adopted code with the manufacturer and a qualified electrician. Fixed electric space heating and portable cord-connected appliances do not share one universal “80% rule,” so this worksheet does not turn a breaker rating into an approved heater size.

    Capacity alone also does not prove uniform crop-zone temperature. Route the air without blowing directly on plants, and keep the control sensor out of the heater discharge and direct sun according to exact equipment instructions. Use the temperature sensor placement guide and the broader greenhouse temperature control sequence after the load calculation.

    5. Treat combustion moisture and venting as load constraints

    An unvented fuel heater does more than add heat. UF/IFAS Extension notes that unvented or improperly vented gas- and oil-fired units can release carbon monoxide, ethylene, sulfur dioxide, unburned hydrocarbons, carbon dioxide, and water vapor; its guidance calls for combustion products to be vented outside and adequate combustion air to be provided.

    The moisture magnitude is large enough to affect the heating decision. US DOE/PNNL guidance estimates about one gallon of liquid-equivalent water vapor per 100,000 Btu from unvented combustion. The US Energy Information Administration lists 91,452 Btu per gallon of propane. Combined, those values imply roughly 0.91 gallon of liquid-equivalent water vapor per gallon of propane burned when that moisture remains inside. This is a cross-source estimate, not a site measurement.

    Do not use this article to design a flue, gas line, regulator, combustion-air opening, or unvented-heater workaround. Choose listed equipment for the actual environment and have fuel-burning systems designed and installed under current manufacturer instructions and local requirements. Plan cold-weather moisture removal with the winter greenhouse ventilation guide; ventilation adds heat demand, so the operating plan and heater design must agree.

    Run this sizing audit before buying

    1. Lock the design temperatures. Record the indoor target, weather station, 99% or 99.6% outdoor condition, and why that risk level fits.
    2. Measure the real envelope. Separate roof, walls, doors, knee walls, and attached boundaries by assembly.
    3. Use traceable U-factors. Prefer exact current manufacturer data; bracket Extension fallbacks when it is missing.
    4. Calculate leakage twice. Use a low and high defensible ACH until measurement supports something narrower.
    5. Add perimeter loss once. State whether the simplified UGA term or another ground-loss method is used.
    6. Compare delivered output. Convert units, then check exact equipment output rather than fuel input or marketing area.
    7. Stop at the power or combustion boundary. No extension cord, power strip, DIY service upgrade, gas piping, or vent improvisation.
    8. Verify control and failure response. Check sensor location, heat distribution, alarm/backup plan, and seasonal readiness with the climate-control checklist.

    Record both the design load and the unresolved inputs. If the answer depends on an unknown U-factor, leakage rate, electrical path, appliance output, or venting condition, the correct result is a range or an escalation—not false precision.

    Sources and method

    This worksheet is an editorial synthesis of UGA, UAF, UF/IFAS, ASHRAE, CPSC, EIA, and US DOE/PNNL guidance. The example was independently recalculated from its visible assumptions. My Greenhouse Lab did not measure a greenhouse or test a heater for this article; exact equipment documentation, site conditions, and qualified design remain controlling.